{"id":6818,"date":"2020-01-10T11:51:42","date_gmt":"2020-01-10T10:51:42","guid":{"rendered":"https:\/\/rittmeyer-beri.de\/?page_id=6818"},"modified":"2026-10-19T10:52:28","modified_gmt":"2026-10-19T08:52:28","slug":"all-round-auto-support","status":"publish","type":"page","link":"https:\/\/rittmeyer-beri.de\/en\/service\/support\/all-round-auto-support\/","title":{"rendered":"ALL.ROUND.AUTO<\/span> – Support"},"content":{"rendered":"\n

Welcome to the support page for our ALL.ROUND.AUTO<\/a>. Here you will find an overview with answers to frequently asked questions as well as video instructions for the machine. Please use the supplied operating manual for more detailed assistance.<\/p>\n\n\n\n

A list of other machines can be found here in the Support<\/a> section. If you have any questions, feel free to contact us directly<\/a>.<\/p>\n\n\n\n

Frequently Asked Questions<\/h2>\n\n\n
\n\t\n
\n\tThe machine does not start \u2013 what can I check?<\/summary>\n\t
\n\t\tCheck if the power cord is properly connected and undamaged, if mains voltage is present, and if the power supply is working. If the green power switch does not light up after turning on, according to the manual, no mains voltage is present. Technical interventions may only be carried out by qualified personnel.\t<\/div>\n<\/details>\n\n\n
\n\tThe main switch lights up but the display remains black \u2013 what should I do?<\/summary>\n\t
\n\t\tCheck the display’s connector. If the connection is correct and the display remains black, turn off the machine and have the cause checked by qualified personnel.\t<\/div>\n<\/details>\n\n\n
\n\tFoot switch or sensor does not trigger \u2013 how do I fix the problem?<\/summary>\n\t
\n\t\tCheck in the menu whether the associated trigger is activated and check the connector of the foot switch or sensor. Only when the correct trigger is active and properly connected can the work cycle be triggered.\t<\/div>\n<\/details>\n\n\n
\n\tThe protective cover is open (Error 1: Cover Open) \u2013 what do I have to do?<\/summary>\n\t
\n\t\tClose the protective cover completely. The machine monitors the protective cover for safety and can only continue operating once the cause of the message is resolved. Protective or safety devices may not be bypassed or tampered with.\t<\/div>\n<\/details>\n\n\n
\n\tThe closing plate or lower safety flap does not close \u2013 what could be the cause?<\/summary>\n\t
\n\t\tRemove objects or material residues that prevent the closing plate from closing completely. Errors 18 Can’t Close<\/strong> or 21 Cannot Open<\/strong> relate to the lower safety flap. If the problem is not resolved by removing a blockage, stop the machine and contact service.\t<\/div>\n<\/details>\n\n\n
\n\tThe message Low Pressure or Input Pressure appears \u2013 how do I proceed?<\/summary>\n\t
\n\t\tCheck the compressed air supply and make sure the pressure regulator is set to 6 bar<\/strong>. The compressed air must be dry, clean, and low in oil. The message means that the input pressure is too low or the required clamping pressure is not reached.\t<\/div>\n<\/details>\n\n\n
\n\tThe cable guide sleeve cannot be screwed in \u2013 what should I do?<\/summary>\n\t
\n\t\tCheck if the holding plate is extended. Manually pull the holding plate to the side according to the instructions and then screw in the cable guide sleeve if necessary. Perform work in the machine area only when the machine is safely switched off.\t<\/div>\n<\/details>\n\n\n
\n\tError Blade Overload or Blade Close \u2013 how can I respond?<\/summary>\n\t
\n\t\tFor Blade Overload<\/strong> (Error 9), a lower blade speed may fix the problem. For Blade Close<\/strong> (Error 10), the cutting force at low speed is not sufficient. Check blades, material, and processing parameters. Before working on blades, switch off the machine, disconnect power and compressed air, and release residual pressure.\t<\/div>\n<\/details>\n\n\n
\n\tHow do I perform a reference run?<\/summary>\n\t
\n\t\tClose the lid and start the reference run via the corresponding button in the main menu. Make sure that the blade type selected in the recipe or reference matches the blades actually used \u2013 including version, cutting position, and for nozzle blades the diameter. A reference run is also part of the functional test before production begins.\t<\/div>\n<\/details>\n\n<\/div>\n\n\n\n

<\/p>\n\n\n\n

Video Tutorials<\/h2>\n\n\n\n

Extended stop – 630mm:<\/h4>\n\n\n\n